Überspannungsschutz für Solarmodule – Ein umfassender Leitfaden zur Auswahl und Beschaffung

Why Your Solar Panels Need Surge Protection – It’s Not Just Lightning

Wenn die meisten Installateure an den Überspannungsschutz für Solaranlagen denken, stellen sie sich einen Blitz vor, der in ein Dach einschlägt. Das ist jedoch nur die halbe Wahrheit. Die andere Hälfte ist leiser, aber genauso zerstörerisch. Netzumschaltungen, Anpassungen der Kondensatorbänke, die Behebung von Netzfehlern und sogar die Schaltkreise des Wechselrichters selbst erzeugen transiente Überspannungen. Diese breiten sich sowohl über die Gleichstrom- als auch über die Wechselstromleitungen aus und suchen nach der schwächsten Stelle in Ihrer Anlage.

Solar installations are uniquely vulnerable. Those long DC cable runs from the array to the inverter act as antennas, coupling electromagnetic energy from nearby lightning strikes directly into your system. A strike doesn’t have to hit the panels – a discharge within 500 meters can induce thousands of volts into PV wiring through electromagnetic coupling alone.

Put the risk in financial terms. A residential string inverter costs $1,500 – $3,000 to replace. A commercial three-phase unit runs $5,000 – $8,000. System downtime during replacement – especially for a commercial installation feeding the grid – can cost thousands more per day in lost energy production. Against that, a quality DC SPD costs $40 – $200 per unit. The math isn’t complicated, but it only works if the SPD is correctly selected, correctly installed, and built with components that don’t degrade after the first surge. The rest of this guide covers all three.

SPD Types for Solar PV – What Goes Where

Surge protection for solar isn’t one device – it’s a coordinated system of devices placed at specific boundaries. Understanding which type goes where is the foundation of everything that follows.

Das Klassifizierungssystem basiert auf zwei Testwellenformen, die verschiedene reale Bedrohungen simulieren:

Think of this as a cascade: Type 1 is the floodgate at the property line, handling the biggest but rarest events. Type 2 is the drainage system throughout the building, handling the frequent but smaller surges that make up 90% of real-world protection needs. For the vast majority of residential and commercial rooftop solar – especially without an external lightning rod system – Type 2 SPDs at the right locations provide effective protection.

Die Mindestausstattung für jede netzgekoppelte Solaranlage: ein Gleichstrom-Überspannungsschutz (SPD) vom Typ 2 am Sammelkasten oder am Gleichstromeingang des Wechselrichters und ein Wechselstrom-Überspannungsschutz (SPD) vom Typ 2 am Wechselstromausgang des Wechselrichters oder an der Hauptschalttafel. Surges enter from both directions – the array side and the grid side – and a device on only one side leaves the other completely exposed.

How to Size a Solar DC Surge Protector – The 4 Numbers on Every Datasheet

Every solar SPD datasheet carries four critical numbers. The most common installer mistake is looking at only one of them – usually the nominal voltage printed on the housing. In reality, these four parameters form an interdependent system. Get any one wrong, and the protection is compromised regardless of what the other three say.

Maximum Continuous Operating Voltage (Uc) – The Cold-Morning Trap

Hier treten die meisten Fehler bei der Dimensionierung auf. Die Uc-Spannung eines SPD (bei Gleichstromgeräten manchmal auch als MCOV oder Ucpv bezeichnet) ist die maximale Spannung, der es dauerhaft standhalten kann, ohne Strom zu leiten. Wählt man einen zu niedrigen Uc-Wert, beginnt das SPD an kalten Wintermorgen, wenn die Spannung Ihrer Anlage ihren Höchstwert erreicht, Strom zu leiten, wodurch die internen Komponenten schon lange vor dem Eintreffen einer Überspannung beschädigt werden.

Here’s why: a solar module’s open-circuit voltage (Voc) rises as temperature drops. A string of 20 modules rated at 41.5V Voc at 25°C doesn’t produce 830V on a -10°C morning – it produces significantly more. The IEC 61643-31 standard provides the correct sizing formula:

Uc ≥ Voc(STC) × [1 + |βVoc| × (Tmin - 25°C)] × 1.1

Beispiel mit Lösung: 20 modules × 41.5V = 830V string at STC. With a typical crystalline silicon temperature coefficient βVoc of 0.0028/°C and a site minimum of -10°C (use your 10-year historical low, not the average winter temperature): corrected Voc = 830 × [1 + 0.0028 × 35] = 911V. Apply the IEC-mandated 1.1 safety factor → 1.002 V. Das bedeutet, dass Sie ein SPD mit einer Nennspannung von 1.200 V, not a 1,000V unit. The standard DC voltage ratings are 600V, 800V, 1,000V, 1,200V, and 1,500V – always round up to the next available rating.

Nominal and Maximum Discharge Current (In / Imax) – Match the Risk, Not the Marketing

Bigger kA numbers sell more SPDs, but they don’t necessarily protect better. More importantly: you cannot directly compare the current ratings of different SPD types. A Type 1 SPD rated at Iimp = 12.5 kA (10/350 μs waveform) handles far more energy than a Type 2 SPD rated at Imax = 40 kA (8/20 μs waveform). The waveform matters – 10/350 μs delivers roughly 20 times the energy of an 8/20 μs pulse at the same peak current.

Bei der praktischen Auswahl sollte die Ableitleistung auf die Blitzgefährdung der Anlage abgestimmt werden:

Ng is the ground flash density – the average number of lightning strikes per square kilometer per year in your installation area, available from national meteorological services or the IEC 62305-2 risk assessment maps. For most of Europe, Ng falls between 0.5 and 4. For Florida, it exceeds 10.

Spannungsschutzstufe (Up) und Kaskadenkoordination

The Up rating tells you the maximum voltage that appears at the SPD’s terminals during a surge event – the “let-through” voltage that reaches your equipment. The rule is simple: Up darf 80% der Impulsfestspannung (Uw) des Geräts nicht überschreiten.. Most string inverters have Uw ratings between 4 and 6 kV, so target an SPD with Up ≤ 3.2 – 4.8 kV.

But there’s a hidden variable that can double your effective Up: lead length. Every 0.5 meters of SPD connection wire adds approximately 0.5 – 1 kV of effective clamping voltage due to lead inductance. This is why installation standards mandate keeping SPD leads under 0.5 meters total – longer leads can negate the protection rating entirely.

If your system requires both a Type 1+2 SPD at the service entrance and a Type 2 SPD downstream at the inverter, maintain at least 10 meters of cable separation between them, or insert a 15 – 25 μH decoupling inductor. Without this coordination, the downstream SPD can be destroyed by reverse voltage reflections from the upstream device.

What’s Inside a Quality Solar SPD – And Why It Matters

Datasheet numbers are a minimum bar, not a quality guarantee. Two SPDs both labeled Uc = 1,200V, Imax = 40 kA can perform completely differently in the field – one still protecting after multiple surge seasons, the other silently degraded after a single moderate event. The difference is inside the housing, in three components that no datasheet fully describes.

The MOV Chip – Why Brand and Tolerance Determine Everything

The metal oxide varistor (MOV) is the heart of every SPD – a semiconductor disk that switches from high resistance to low resistance in nanoseconds when voltage exceeds its threshold, shunting surge current to ground. When the surge passes, it must return to its high-resistance state instantly. An MOV that stays partially conductive after a surge becomes a heating element, degrading until thermal runaway.

The quality difference starts with manufacturing tolerance. MOVs are sorted by their breakdown voltage window: ±5% (Tier 1, used by Littelfuse and TDK/EPCOS), ±10% (professional grade, used by manufacturers who specify branded MOVs like Taiwan’s LKD), ±20% (typical commodity MOVs), and “unsorted” (the cheapest factories). A tight tolerance means the MOV triggers precisely at its designed voltage – not 15% too high (leaving equipment unprotected) or 15% too low (conducting during normal operation and wearing out prematurely).

The second discriminator is encapsulation. Quality MOVs use epoxy-sealed encapsulation (“-G”) that provides moisture resistance, electrical insulation, and physical protection during transport. Low-cost alternatives use bare chips dipped in AB glue – cheaper, but vulnerable to humidity ingress that shifts the breakdown voltage over time. After a standard 8/20 μs impulse test (In = 20 kA, 10 strikes alternating polarity), a quality MOV’s three key parameters – leakage current (μA), residual voltage (kV), and nonlinear coefficient (α) – remain stable. A commodity MOV shows measurable drift on all three after just 2 – 3 strikes, meaning its protection characteristics have already changed.

The Disconnection Mechanism – What Happens When the SPD Sacrifices Itself

An SPD at the end of its life must disconnect itself from the circuit. If it doesn’t – or if it disconnects incompletely – it becomes a fire hazard. The disconnection mechanism is therefore the most safety-critical component in the entire device, yet it’s almost never discussed in SPD selection guides.

The core technology is the low-temperature solder joint. When an MOV degrades and begins to heat up continuously, the solder joint at a specific contact point must melt at a precise temperature – triggering a spring-loaded disconnection plate that physically separates the contacts. The temperature window is critical and product-specific: too low and the joint melts during a normal surge (false trip); too high and the MOV catches fire before the joint releases.

Hier liegt die technische Herausforderung, die gut konzipierte Überspannungsschutzgeräte (SPD) von den übrigen unterscheidet: Die Norm IEC 61643-11 schreibt vor, dass SPDs zwei Prüfungen bestehen müssen, die gegensätzliche Anforderungen an diese Lötstelle stellen. Die Blitzimpulstest (8/20 μs, high current, milliseconds) tries to prevent the joint from melting – the SPD must survive the surge without disconnecting. The Prüfung der thermischen Stabilität (low continuous current, 2 – 3 days) requires the joint to melt reliably as the MOV degrades. Some manufacturers handle this contradiction by testing different units for each standard – one batch for impulse, another for thermal. A properly engineered SPD passes both tests on every unit.

The second critical element is the arc-extinguishing design. When the solder melts and the disconnection plate springs open, a DC arc can form between the separating contacts – especially in PV DC circuits where there’s no zero-crossing to extinguish the arc naturally. Inferior designs allow the arc to persist through thin solder filaments that stretch rather than snap, maintaining a conductive path. The result: the SPD thinks it’s disconnected, but current continues to flow through the arc, eventually igniting the plastic housing. An independent arc-extinguishing chamber – where the disconnection plate physically partitions the contacts into separate compartments – prevents filament formation and starves any arc of ionized gas. During selection, ask the supplier how their disconnector handles DC arc extinction specifically. A vague answer is a red flag.

Kontakte, Wohnen und die Dinge, über die niemand spricht

The structural components of an SPD – the metal pins that plug into the base, the plastic housing that contains the assembly, the terminals that carry load current – are where cost-cutting is most common and most invisible to a datasheet reader.

Kontaktstifte aus Metall. The pins that connect the pluggable SPD module to its base carry the full surge current during a strike. If the contact area is insufficient, the interface resistance generates heat – and in extreme cases, the electromagnetic forces from a high-current surge can physically eject the module or crack the base. Industry-typical pin dimensions are 4 – 7 mm wide × 0.4 – 0.6 mm thick. A small number of manufacturers use 8 mm × 0.8 mm pins – roughly 45% more cross-sectional area – reducing contact resistance, heat generation, and the risk of mechanical failure during high-energy surges.

Gehäusematerial. When an SPD reaches end-of-life and its internal temperature rises toward the disconnection trigger point, the plastic housing must not ignite or deform before the disconnector activates. PA6 with 30% glass fiber reinforcement (PA6+GF30%) is the standard material for quality SPD housings, offering high heat deflection temperature and inherent flame retardancy. The verification is the glow wire test – a heated wire applied to the plastic at a specified temperature to confirm it doesn’t ignite. Ask for glow wire test documentation covering every plastic component in the SPD, not just the main housing.

Korrosionsbeständigkeit. A 48-hour salt spray test per IEC 60068-2-11 simulates the corrosive environment of sea freight – a practical concern when SPDs ship from manufacturing hubs in Asia to installation sites in Europe, Africa, or the Americas. Metal components (terminals, screws, springs, and contact pins) that aren’t salt-spray tested can arrive at the job site with surface corrosion that compromises electrical contact. If a supplier can’t produce salt spray test reports for their metal components, factor in a higher rate of early-life contact failures – especially for coastal installations.

These structural details aren’t abstract ideals – they’re verifiable procurement criteria. A small number of manufacturers, including LSP, build their production around precisely these investments: 8 mm × 0.8 mm contact pins with 45% greater cross-section than the industry typical, PA6+GF30% housings backed by full glow wire test documentation, and 48-hour salt spray testing on every batch of metal components. Before specifying an SPD, ask for three things: the pin dimension specification, the glow wire test certificate for the housing material, and the salt spray test report for all current-carrying metal parts. A supplier who can produce all three – and who manufactures on a proprietary mold rather than a public commodity mold – has made structural quality a production priority rather than a marketing claim. For a look inside a production SPD and what these design differences mean in practice, see a detaillierte interne Demontage.

Installationsvorschriften, die über den Erfolg oder Misserfolg Ihres Überspannungsschutzes entscheiden

An SPD selected perfectly but installed poorly is worse than no SPD – it creates a false sense of security. Three installation details determine whether the device actually protects anything.

Leitungslänge. This is the single most violated installation rule. The total length of SPD connection conductors – from the busbar tap point to the SPD terminal and from the SPD ground terminal to the earth bar, L+ and L- combined – must not exceed 0.5 meters. Beyond this, the inductance of the wire itself adds voltage drop during the surge’s rising edge. Every additional 0.5 meters of lead length tacks on roughly 0.5 – 1 kV of effective clamping voltage, directly canceling the SPD’s rated Up. If the SPD is rated Up = 2.5 kV but your leads add 2 kV, the equipment sees 4.5 kV – potentially above its withstand rating. Keep leads short, straight, and twisted together (L+ and L-) to minimize loop area and mutual inductance.

Erdungsqualität. An SPD dumps surge energy to ground. If the ground path has high impedance – long runs, coiled conductors, corroded connections, or loose bonding – that energy finds an alternative path, often through your equipment. The ground conductor should be as short and straight as physically possible. All metallic components in the PV system – module frames, mounting rails, conduit, junction boxes, inverter enclosures – must be bonded to the equipment grounding conductor. A surge looking for earth will take the lowest-impedance path; make sure you’ve provided one.

Konfigurationsmodus. Most modern transformerless (floating/IT) inverters require a 3-mode Y-configuration for DC-side SPDs: protection between L+ to PE, L- to PE, and L+ to L-. Systems with a functionally earthed negative rail use 2-mode protection (L+ to PE and L- to PE). Installing a configuration mismatched to your inverter’s grounding scheme leaves one protection path open – and surges are opportunistic.

How to Verify SPD Quality Before You Buy – A Solar Installer’s Checklist

Sie haben die Spannung richtig bemessen, die Ableitleistung an Ihre Blitzschutzzone angepasst und die entscheidenden Details zum inneren Aufbau ermittelt. Nun liegen Ihnen Angebote von drei Anbietern vor, deren Preise um den Faktor drei variieren. Zwei Überprüfungsschritte trennen eine fundierte Beschaffung vom Glücksspiel.

Certification Verification – Check the Database, Not the Logo

A CE mark on an SPD housing is a manufacturer’s self-declaration – it means the company claims compliance, not that an independent lab confirmed it. TÜV, CB, and UL marks are different: they require testing by an accredited third-party laboratory whose results are published in a publicly searchable database. Yet fake and expired certificates are common enough that the logo alone proves nothing.

Für Solar-Gleichstrom-Überspannungsschutzgeräte gilt folgende Norm: IEC 61643-31 (PV-spezifisch). Bei SPDs auf der Wechselstromseite beträgt sie IEC 61643-11. Bevor Sie sich für einen Anbieter entscheiden, notieren Sie sich die Zertifikatsnummer aus dessen Unterlagen und überprüfen Sie diese in der offiziellen Datenbank der ausstellenden Stelle: im Zertifikatsprüfer des TÜV Rheinland unter www.tuv.com, in der Online-Zertifikatsdatenbank des IEC CB-Schemas oder bei UL Product iQ für nordamerikanische Produkte. Drei Punkte sind zu prüfen: Das Zertifikat muss gültig sein (d. h. nicht abgelaufen oder ausgesetzt), die auf dem Zertifikat angegebene Produktmodellnummer muss genau mit dem von Ihnen gekauften Gerät übereinstimmen, und der zertifizierte Spannungsbereich muss Ihre tatsächliche Systemspannung abdecken (akzeptieren Sie keinen für 600 V zertifizierten SPD für einen 1.000 V-String).

Total Cost of Ownership – Why the Cheapest SPD Usually Costs the Most

A $35 DC SPD replaced three times over five years – plus three truck rolls at $150 each for labor – costs $555. A $90 SPD rated for the same voltage and current, with a documented 5-year warranty and components designed for multi-strike durability, costs $90 plus one installation. That’s a $465 difference in the wrong direction. Add the risk of an inverter replacement ($1,500 – $8,000) if the cheap SPD fails silently between inspections, and the procurement decision reframes itself.

The TCO formula is straightforward: purchase price + installation labor + (number of expected replacements × replacement cost) + downtime cost + risk-adjusted equipment damage cost. The industry-standard SPD warranty is two years. A supplier offering five years is making a statement about expected service life, not just marketing – warranty periods in this industry correlate directly with MOV quality and disconnection mechanism reliability.

When evaluating SPD suppliers for your solar installations, look beyond the datasheet. Ask for salt spray test reports, glow wire test documentation, and the MOV brand and tolerance specification. LSP offers free evaluation samples with full technical documentation and a 5-year warranty – Ein Muster anfordern um die in diesem Leitfaden behandelten Qualitätsstandards für die Bauausführung zu überprüfen.

Literaturverzeichnis

1. Bourns. “SPDs for Photovoltaic Applications – Application Note.” https://www.bourns.com/docs/technical-documents/technical-library/outside-plant-products/bourns_spds_for_photovoltaic_applications_appnote.pdf
2. Hasse, Peter. Überspannungsschutz von Niederspannungsanlagen, 2. Auflage. IET Energy Engineering Series. ISBN 978-0852967812.
3. LSP Global. https://lsp.global/
4. LSP Global – Contact. https://lsp.global/contact-us/
5. LSP. “SPD Internal Teardown”. YouTube. https://www.youtube.com/watch?v=gskNxtACRLE